Convert cable from USB to RS232(standard DTE interface).1 meter,with communication indicator,support traditional RS232 PLC prgramming cables.

USB-CIF31 is the real USB to RS232 interface converters. Under the control of computer-driven driver, the programming cable makes it possible for the computer's USB interface to simulate the traditional serial (known as COM interface), thus various existing programming software such as communications software, monitoring software and other applications can be normally used. The working power supply of this cable is directly from the USB port, but not the PLC programming interface. The two-color LED on the converter box indicates data’s transceiving status.

The RS232 ports of the USB-CIF31 are standard DTE interface (DB9M-Block, the same with the computer's serial port RS232). Its signal as shown below：

USB-CIF31 do a very good simulation as a RS232 serial port, and even direct operate hardware by I/O. for the user，just like to visit the physical RS232 ports. USB-CIF31 can be used to support majority of the traditional PLC cable programming, and this point is different from similar products on the market .the appendix will show the test results of the USB-CIF31 connection with various traditional RS232 interfaces with PLC programming cable communications.

Features and technological index:

● the operating system can support of the USB-CIF31 : Windows2000/XP (WinNT4/95/98/Me/DOS does not support)

● fully compatible with USB V1.1 and norms of USB CDC V1.1

● USB bus powered, the current consumption is about 50 mA

● baud rate: 300 bps ~ 1Mbps automatically adapt to the standard baud rate

● support UART data format: data bits: 7-8, stop bit: 1, 2, check-bit: odd / even / no parity

● each PC only support a USB-CIF31

● temperature: -20 ~ +75 ℃

● Cable length: 1 m, colors: black

Usage of USB-CIF31：

USB device drivers should be installed before using USB-CIF31 programming cable, which are available on the CD-ROM sold together with the cable. And for the specific installation steps, please refer to the instruction files on the CD-ROM drivers, and details are not necessarily listed here.

After completing Driver installation, the corresponding COM port for the USB-CIF31 programming cable will be displayed in the “Device Manager” of Window. The step next is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. And the following steps are exactly the same as in the traditional programming cables with RS232 interfaces..

Appendix of USB-CIF31：

the success test data of the USB-CIF31 connecting with the traditional PLC programming cable (Win2000/XP operating system)

The quality is guaranteed.It's tested before shippment.Not made by Omron,OEM product as the replacement.

the connection cable between Computer RS232 interface and RS232 interface of Omron PLC or Omron touch panel,2 meters

Made by us,OEM compatible one,but the quality is 100% guaranteed,1 year warranty.

USB-XW2Z-200S:USB/RS232 interface,cable for Omron PLC Programming,3 Meters,RS232 interface with communication indicator.

USB-XW2Z-200S is the programming cable in which USB interface provided both the serial connection and RS232 signal conversion. Under the control of computer-driven driver, the programming cable makes it possible for the computer's USB interface to simulate the traditional serial (known as COM interface), thus various existing programming software such as communications software, monitoring software and other applications can be normally used. The working power supply of this cable is directly from the USB port, but not the PLC programming interface. The two-color LED on the converter box indicates data’s transceiving status.

USB-XW2Z-200S is applicable to Omron PLC, with a direct connection to the RS232 interfaces (DB9F- Hole Block) on all models of Omron PLC or the Omron touch panel RS232 interface (DB9F-Hole Block).

Outline configuration:

Features and technological index:
● Support USB-XW2Z-200S programming software version: CX-Programmer V1.0 and above
● Fully compatible with USB V1.1 norms and USB CDC V1.1
● USB-bus powered, with current consumption of 50 mA
● Baud rate: 300 bps ~ 1Mbps automatically adapt to the standard baud rate
● Support UART data format: data bits: 7-8; stop bit: 1, 2; check-bit: odd / even / no parity
● Each PC only supports one USB cable programming
● Working temperature: -20 ~ +75 ℃
● Cable length: 3 m; Color: black

Usage:

USB device drivers should be installed before using USB-XW2Z-200S programming cable, which are available on the CD-ROM sold together with the cable. And for the specific installation steps, please refer to the instruction files on the CD-ROM drivers, and details are not necessarily listed here.

After completing Driver installation, the corresponding COM port for the USB-XW2Z-200S programming cable will be displayed in the “Device Manager” of Window. The step next is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. And the following steps are exactly the same as in the traditional programming cables with RS232 interfaces.

USB- CIF02:USB interface Omron series PLC programming cable,with communication indicator,cable connection between CQM1,CPM1, CPM1A, CPM2A,C200HS,C200HX/HG/HE,SRM1 series PLC and the computer. After connected with CS1W-CN114 cable,it can also be connected with CS/CJ,CQM1H and CPM2C series PLC. 3 Meters

USB-CIF02 programming cable simulates USB port as traditional serial port (usually COM3).The working power supply of this cable is directly from the USB port, but not the PLC programming interface. The two-color LED on the converter box indicates data’s transceiving status.

USB-CIF02 is applicable to Omron PLC,which can directly connect with CPM1,CPM1A,CPM2A,CPM2AH,C200HS,C200HX/HG/HE and SRM1 series PLC; for CS / CJ, CQM1H and CPM2C series PLC , please choose USB-CN226 programming cable, but also can connect with CS / CJ, CQM1H and CPM2C series PLC via CS1W-CN114 cable adapter.

Note: USB-CIF02 can not be used to the old model C200H, C_ _ H, C500-AP003, 3G2A5-AP003 series PLC.

Outline configuration of USB-CIF02:

Features and technological index of USB-CIF02:
● Support USB-CIF02 programming software version: CX-Programmer V1.0 and above
● fully compatible with USB2.0 norms
● USB-bus powered, with current consumption of 50 mA
● Baud rate: 300 bps ~ 1Mbps automatically adapt to the standard baud rate
● Support UART data format: data bits: 7-8; stop bit: 1, 2; check-bit: odd / even / no parity
● Each PC only supports one USB cable programming
● Working temperature: -20 ~ +75 ℃
● Cable length: 3 m; Color: black

Usage:

USB device drivers should be installed before using USB-CIF02 programming cable, which are available on the CD-ROM sold together with the cable. And for the specific installation steps, please refer to the instruction files on the CD-ROM drivers, and details are not necessarily listed here.

After completing Driver installation, the corresponding COM port for the USB-CIF02 programming cable will be displayed in the “Device Manager” of Window. The step next is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. And the following steps are exactly the same as in the traditional programming cables with RS232 interfaces.

Long-distance communications:

 USB-CIF02 programming cable does not support long-distance communication. For long-distance communication, RS485/422 communication module can be chosen (model: FS-CIF11), which makes dozens of PLC communicate, with the largest communication range of up to 2 Km.  
Please Note: USB interface cannot be extended.

The quality is guaranteed.It's tested before shippment.Not made by Omron,OEM product as the replacement.